Panasonic WV-CU650 Provozní pokyny

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WV-CU650Sy

10@8 Shuttle hold button (SHUTTLE HOLD)• If you press this button while rotating the shuttle ring,playback speed will be maintained even after removin

11● Rear ViewDC9V INMODEDATASERIALCONTROLLERNO.JOYSTICK$8 $9$7$6$5$4$4 Joystick connector (JOYSTICK)This connector is used for connection with the joy

12%0 Top buttonThe top button is pressed to recall a function alreadyassigned.%1 Zoom wheel controllerThis controller is used for zooming cameras equi

13 LCD Display DescriptionsThe following are examples of LCD display after login.Note: Some parts of LCD displays, described on this document, may di

14● Main Menu (Menu Functions)LCD MENU CAM 101Camera Setupq CategoryThe category of selected menu function is displayed.w Function numberThe funct

15● Messages Displayed on the LCDInvalid InvalidThis message is displayed in the following circumstances.• When you have entered a wrong user ID

16INSTALLATIONS AND CONNECTIONSWARNINGThe installations described in the figures should bemade by qualified service personnel or systeminstallers. Ba

17 Connection with the 3D Joystick UnitConnect the main unit and 3D joystick unit as follows.Note: Use the main unit and 3D joystick unit whose combi

182. Set the Line termination switch of other system con-trollers to OFF.● Setting for Terminal ModeSet the MODE Switch #1 and #5 to ON.Note: Refer to

19SETUP PROCEDURES (FIRMWARE) Administrator Password EntryIf you log into the system in the administrator mode,PS·Data communication setting, all res

The serial number of this product may be found on the bot-tom of the unit.You should note the serial number of this unit in the spaceprovided and reta

20 All ResetWhen the all reset mode is activated, all of the following set-tings will be reset to the factory default.• Administrator password• PS·Da

213. Enter the administrator password.The password entered will be displayed as “∗” marks.Notes:• The factory default is “650”.• To delete a character

223. Select a desired parameter by rotating the JogDialor pressing the + or – button.You can select the desired parameter from “1” (bit) and“2”. The f

23● Group Address Setting for SystemControllerNote: Remain the factory default. When you have mistaken-ly changed the setting, recover the factory def

24 To Change the AdministratorPasswordYou can change the administrator password. The factorydefault is “650”. ● Operation1. Turn off the power.2. Tur

25 Database CopyYou can copy the database from the source system con-troller (CONTROLLER NO. switch is set to 1.) to destinationsystem controllers (C

26The LCD display of destination system controller(s)becomes as follows.Note: If the check sum is not identical, check the con-nection of all the cont

27BEFORE OPERATION Power-onBefore operation, confirm the system composition.Depending on system composition, some functions may beunavailable.1. Plug

28 Basic Operation FlowSystem Unit SelectionMonitor SelectionCamera SelectionSystem UnitSetup and OperationCamera setupand controlSystem OperationLog

29● Button Buzzer SettingYou will perform the setting whether to activate a soundwhen a button is pressed. Select the desired parameter byrotating the

3IMPORTANT SAFETY INSTRUCTIONS1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this

30 If You Have Forgotten the LoginPasswordRefer to the system administrator. Operation Start (Auto Login)When auto login is set to ON, operators can

31 Recorder SelectionNotes:• In advance, you need to set HDD-unit maps. (Refer top. 67 Associating Recorder Numbers with UnitNumbers.)• In the factor

32Note: If camera numbers are associated with unit num-bers, you can skip system unit selection. (Refer top. 66 Associating Camera Numbers with UnitNu

33 Tour Sequence/Group SequenceSequence monitoring is the function to switch cameraimages automatically, according to the order registered inthe syste

341. Select a desired monitor. (Refer to p. 32 MonitorSelection.)2. To toggle the OSD information, press the OSD button. Note: OSD information differs

35From this system controller, you can control digital diskrecorders supporting PS·Data. You will control a recorder inthe status in which a recorder

36Available buttons and functionsF1 button: Thumb or ListChanges the monitor display between the recording eventlist window and thumbnail menu.F3 butt

373. To determine the filter setting, press the CAM (SET) but-ton of main unit or top button of 3D joystick unit.The searching filter window will appe

384. Enter the desired date and time by performing either ofthe following.• Rotate the JogDial clockwise or counterclockwise.• Press the + or – button

392. Select a desired group to play back by rotating theJogDial.3. Press the PLAY/PAUSE or CAM (SET) button again.The image on the specified date and

IMPORTANT SAFETY INSTRUCTIONS ...3PREFACE ...5FEA

40You can control cameras from this system controller. Camera Panning/Tilting ControlThe following procedure is available when panning/tiltingheads o

41 Preset Position ControlPreset position is the function to register camera monitoringpositions (preset positions) associated with position num-bers

42 Camera Position ControlCamera position is the association of camera numbers andpreset position numbers. Up to 1 000 camera positions areregistrabl

43 Defroster ControlThe following procedure is available when a selected cam-era (housing) is equipped with a defroster.1. Select a system unit, moni

44 System Controller Behaviorduring the Alarm ModeWhen an alarm signal is input to cameras or system units,this system controller is notified that an

45<Joystick unit>3D joystick upward (▲): Moves the cursor up.3D joystick downward (▼): Moves the cursor down.3D joystick to the left (t): Moves

46● Operation (WJ-HD200 Series)Note: WJ-HD200 Ver. 1.24 later or WJ-HD220 supportsalarm history search. (Refer to the operating instruc-tions of recor

47MENU FUNCTION DESCRIPTIONSYou can assign frequently-used menu functions (system functions and camera functions, etc.) to the F1 to F8 button of syst

48Auto Pan SetupYou will perform the auto pan setting of camera.Note: Refer to the operating instructions of camera fordetails on the auto pan functio

49● System Functions (SYS)System SetupYou will open the setup menu of system unit and changethe settings.SX150 OSD (WJ-SX150 Series only)This function

5PREFACEThis product, System Controller WV-CU650, is designed for setup and operation of cameras and other system units installed ina surveillance sys

50Cam-Unit MapYou will register cam-unit maps (the association of cameranumbers and unit numbers).HDD-Unit MapYou will register HDD-unit maps (the ass

51Camera +1The image of camera with the higher channel number willbe displayed.Camera –1The image of camera with the lower channel number will bedispl

524. Press the ENTER or CAM (SET) button.The sub menu of selected function will appear on theLCD.5. Perform the operations to activate the selected fu

532. Select a desired function.Select a desired category by rotating the shuttle ring.3. Select a function name by rotating the JogDial.• You can skip

54 To Check Button Functions andJoystick Button FunctionsYou can check the functions assigned to the function (F1 toF8) buttons and joystick function

55MENU FUNCTION DETAILS Camera Functions● Camera SetupYou can display the setup menu of selected camera on theactive monitor.Note: The details on th

562. Press one of the F1 to F4 buttons.BW mode will be activated.Available buttons and functionsF1: OnChanges the camera image from color to black and

57● Auto Pan Setup and ActivationYou will set up and activate the auto pan function. The cam-era can pan between the start and end points you will set

58● Filtering ON/OFF(WJ-HD300 Series Only)During the filtering playback, the searching filter will betemporarily canceled or recovered.1. Display “HD3

59Available controls and functions<Main unit>Shuttle ring clockwise: Moves to the next page.Shuttle ring counterclockwise: Moves to the previous

6PRECAUTIONSLIMITATION OF LIABILITYThis product is a system controller to operate PS·Data sys-tem units and connected cameras. (A surveillance control

60Note: To return the cursor to the previous item, rotatethe shuttle ring counterclockwise or move the 3Djoystick to the left.5. Press the F1 button.C

61Display pattern Display ExampleDD/MM/YYYY HH:MM 24 21/08/2001 22:55 24 *2MM/DD/YYYY HH:MM 24 08/21/2001 22:55 24DD/Mmm/YYYY HH:MM 24 21/Aug/2001 22:

624. Enter a user ID by pressing the numeric buttons.“1” to “99999” are available for the user ID number.Note: If you have entered a wrong user ID, p

6310. Set the camera level by performing either of the follow-ing.• Rotate the JogDial clockwise or counterclockwise.• Press the + or – button.Notes:•

644. Select a desired function by performing one of the fol-lowing.• Rotate the JogDial clockwise or counterclockwise.• Press the + or – button.• Ente

654. Select a desired camera channel by performing one ofthe following.• Rotate the JogDial clockwise or counterclockwise.• Press the + or – button.•

666. Select a desired preset position number by performingeither of the following.• Rotate the JogDial clockwise or counterclockwise.• Press the + or

67Note: To return to Step 3, rotate the shuttle ring coun-terclockwise or move the 3D joystick to the left.5. Select a desired unit number by performi

686. Press the ENTER or CAM (SET) button again.The specified recorder number and unit number will beset for the selected HDD-unit map.“Memory” will ap

69 Joystick Button FunctionsIf you register a joystick button function to a function buttonor joystick function button, you can activate the associat

7DOCUMENT CONVENTIONThis document uses the following convention when describing the use and operation of this unit. System controller: Panasonic Syste

70● Auto PanYou can activate the auto pan mode for the selected cam-era.Note: Refer to the operating instruction of camera fordetails of this function

71● Home PositionYou can move the selected camera to the home position.Note: Refer to the operating instruction of camera fordetails of this function.

72Notes: • To quit the repeat playback, press the F1 buttonagain. “Cancel” will appear on the LCD for a fewseconds.• When the A – B repeat playback fu

73● Alarm Search (WJ-HD200 Series /WJ-HD100 Series)You can move the playback start point to the next alarmrecord of recorded image data.Note: Refer to

74Refer to p. 27.TROUBLESHOOTINGCheck the following before requesting repair.If a trouble cannot be corrected even after checking and trying remedy, c

75The power cord insulation is damaged. The power cord or the plug is damaged.If you continue to use it, a fire or an elec-tric shock may occur. Unplu

76● DATA PortRS-485 PortSystem controller’s rear panel● System ControllerPower Source: 9 V DC, 300 mA (using the supplied AC adapter)Power Source (Sup

77

NM0504-1054 3TR002330BAA Printed in JapanPANASONIC CANADA INC.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010PANASONIC

8MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Main Unit● Front ViewNote: Although printed on the template, some button func-tions are not mentioned h

9o Camera function/System function button (CAM FUNC/SYS FUNC)• Recalls a function of camera by the function number.• When you press while holding down