Panasonic WJMP204 Provozní pokyny

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WJ-MP204Da

10Address setting varies from one communication mode to another.The setting should be made by qualified service personnel or system installers. Panas

11The Setup menu consists of two main menus: one for communication setup for connection to cameras and the system con-troller WV-CU360, and the other

12WJ-MP204 SETUP MENU X.XX COMMUNICATION SYSTEM Displaying the Setup Menu forPanasonic Security Data Mode1. Check that the cameras and peripheral

13 COMMUNICATION UNIT ADDRESS 1 BAUD RATE 9600 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 WAIT TIME OFF(6) Wait Time Settin

14OFF by pressing button 3 (–) or button 4 (+).The initial factory setting is ON.• Terminal Alarm Setting1. Display the SYSTEM menu.2. Move the cursor

15(2) Comp/VD2/Data Setting• Camera Input Setting1. Display the SYSTEM menu.2. Move the cursor to CAMERA IN by pressing button 1(C) or button 2 (D), p

16WJ-MP204 SETUP MENU X.XX COMMUNICATION SYSTEM Displaying the Setup Menu ofCamera Communication Mode1. Check that the cameras and peripherals ar

17(4) Parity Check Setting1. Display the COMMUNICATION menu.2. Move the cursor to PARITY CHECK by pressing button1 (C) or button 2 (D), then select th

18 System Setup for CameraCommunication Mode1. Display the Setup menu.2. Move the cursor to SYSTEM by pressing button 1 (C)or button 2 (D), then pres

19ON: Multiplex sync signals (VD2) are generated by syn-chronizing with the signals sent to the VS/VD INconnector. If there is no input signal, the in

2ENGLISH VERSIONThe serial number of this product may be found on the bot-tom of the unit.You should note the serial number of this unit in the spacep

20Joint metalRemove 2 screws from the rear beforehand.Rack mountingbracket (small)Rack mountingbracket (small) Mount screw Binding head (M3x8)Mount sc

21 BASIC SYSTEM CONNECTION (Panasonic Security Data Mode)The Data Multiplex Unit WJ-MP204 may be connected to cameras, video monitors, and system con

22● Connecting Two or More Data Multiplex Units to System Controller WV-CU360(Panasonic Secuarity Data Mode)SD RDIN INCAMERA RS485ABABGVS/VDSPOT DATAA

23● Connecting Two or More Data Multiplex Units to Matrix Switcher WJ-SX350 (CameraCommunication Mode)TRIN INCAMERA RS485ABABGVS/VDSPOT DATAALARM / RE

24Pin #123456 (1CH)For AlarmInputAlarm OutputAlarm Recover InputAlarm Reset OutputSpot SW InputSpot SW OutputAlarm Input 1 Alarm Output 1(Camera Site

2512340/5VO.C4321ON OFFSW702SW704FixedOnly displays the Setup menu to SPOT OUT.Displays the Setup menu to CAMERA OUT (1 - 4) and SPOT OUT.ONSW7021 OFF

26 Connection to WV-CU360● Basic ConnectionConnect the DATA port on the Data Multiplex Unit to one of the DATA port on the System Controller with the

27 Controlling the CameraFunctions with the DataMultiplex Unit WJ-MP204Before starting operation, loosen the screw on the frontcover with a screwdriv

28ALARM CONTROL FUNCTIONSALARM 001 Alarm InputThe Data Multiplex Unit processes the following alarms.(As to setting, see page 14, 18 and 19.)• Camera

29SPECIFICATIONSSTANDARD ACCESSORYPower Source : 220 - 240 V AC 50 HzPower Consumption : 7 WCamera Input : 1 V[p-p]/75 Ω x 4Spot Input : 1 V[p-p]/75 Ω

3CONTENTSPREFACE ...

Function30CameraSelectionAlarm ResetAlarm SuspendWJ-MP2044321RESETALARMSETSUSPENDALARMWV-CU360Alarm SuspendResetSETSUSPENDALARMAPPENDIX Operation of

N1299-1030 YWV8QA5360BN Printed in JapanN 19 Gedruckt in JapanImprimé au JaponImpreso en Japón2000 © Matsushita Communication Industrial Co., Ltd. Al

4PREFACEFEATURESThe WJ-MP204 Data Multiplex Unit enables you to remotecontrol multiple surveillance cameras, check alarm set-tings, operate the camera

5PRECAUTIONS• Refer all work related to the installation of thisproduct to qualified service personnel or systeminstallers.• Do not block the ventilat

6MAJOR OPERATING CONTOROLS AND THEIR FUNCTIONSq Power Switch (POWER ON/OFF)Press once to turn on the Data Multiplex Unit. The switch remains down (;)

7 Rear Viewo Camera Input Connectors 1-4 (CAMERA IN 1, 2, 3, 4)These connectors accept the composite video signalfrom the camera.!0 Camera Output Con

8Follow the procedures below for setup.1. Press the Power Switch back to the OFF position.Check that the Power Switch LED is off.SETUP PROCEDURE2. Set

9Before connecting the Data Multiplex Unit, check how theDIP switches are set on the rear panel in cases where thesystem setup must be changed. Setti