Panasonic WJSX350 Provozní pokyny stáhnout pdf (Strana 43)

-41-

P C C O M.

B A U D R A T E 1 9 2 0 0

D A T A B I T 8

P A R I T Y C H E C K N O N E

S T O P B I T 1

X O N / X O F F O F F

W A I T T I M E O F F

C A M P O R T S E L E C T

CAM

CAM CAM

0 1 1 0 9 2 1 7 1 2 5 2

0 2 1 1 0 2 1 8 1 2 6 2

0 3 1 1 1 2 1 9 2 2 7 2

0 4 1 1 2 2 2 0 1 2 8 2

0 5 1 1 3 – 2 1 1 2 9 2

0 6 1 1 4 2 2 2 – 3 0 –

0 7 1 1 5 – 2 3 – 3 1 –

0 8 1 1 6 – 2 4 – 3 2 –

3. PC COM. (PC Communication)

This table is used to set the Communication Parameters

between the Personal Computer and the Matrix

Switcher.

Select PC COM. on the SYSTEM menu by moving the

Joystick Controller, then press the CAM (SET) button to

display the PC COM. menu as shown below.

1. Move the cursor to the BAUD RATE parameter by

moving the Joystick Controller. Then set the Baud

Rate to 2400, 4800, 9600 or 19200 by pressing the

+1CAM INC or –1CAM DEC button.

2. Move the cursor to the DATA BIT parameter by

moving the Joystick Controller. Then set the Data

Bit to 7 or 8 by pressing the +1CAM INC or –1CAM

DEC button.

3. Move the cursor to the PARITY CHECK parameter

by moving the Joystick Controller. Then set Parity

Check to ODD, EVEN or NONE by pressing the

+1CAM INC or –1CAM DEC button.

4. Move the cursor to the STOP BIT parameter by

moving the Joystick Controller. Then set the Stop Bit

to 1 or 2 by pressing the +1CAM INC or –1CAM

DEC button.

5. Move the cursor to the XON/OFF parameter by

moving the Joystick Controller. Then set the Mode

to ON or OFF by pressing the +1CAM INC or

–1CAM DEC button.

6. Move the cursor to the WAIT TIME parameter by

moving the Joystick Controller. Then set the Wait

Time to 100, 200, 400, 1000 or OFF by pressing the

+1CAM INC or –1CAM DEC button.

7. After completing the table, press the MON (ESC)

button to escape from the programming mode and

return to the previous SYSTEM menu.

4. CAM PORT SELECT (Camera Port

Select)

This table is used to select either RS485 port 1 or 2 for

the cameras.

Up to sixteen (16) cameras can be assingned to each

port.

Move the cursor to CAM PORT SELECT on the SYSTEM

menu by moving the Joystick Controller, then press the

CAM (SET) button to display the CAM PORT SELECT

menu as shown below.

1. Move the cursor to a Camera Number parameter by

moving the Joystick Controller. Then set the

Camera Port to 1, 2 or – by pressing the +1CAM

INC or –1CAM DEC button.

1: Communicates through port 1

2: Communicates through port 2

–: No communication

Note: Select 1 or 2, if the associated camera site

units are connected. If not, always set the para-

meter to “–”.

2. Repeat the above procedure for the other Camera

Numbers until the table is completed.

3. After completing the table, press the MON (ESC)

button to escape from the programming mode and

return to the previous SYSTEM menu.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 67 68

Komentáře k této Příručce

Žádné komentáře

Panasonic WJSX350 Provozní pokyny Strana 43

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní kamery Panasonic WJSX350