Panasonic WV-SW138 Instalační příručka

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number i

10Keep SDXC/SDHC/SD memory cards (option) away from infants and children. Otherwise, they may swallow the cards by mis-take. In this case, consult a d

11card will be deleted when formatted. If an unfor-matted SD memory card or an SD memory card formatted with other devices is used, this product may n

12Precautions for installationPanasonic assumes no responsibility for injuries or property damage resulting from fail-ures arising out of improper ins

13Do not remove or loosen the internal cam-era screwsDo not loosen the internal camera screws. Otherwise, water exposure may cause damage or malfuncti

14Major operating controlsAbout the initial set buttonAfter turning off the power of the camera, turn on the power of the camera while holding down th

15 Use a slotted head screwdriver to open the screw covers (2 places), and then loosen the 2 screws (M3). Remove the enclosure. • Hold both sid

16PreparationsYou can install the camera on a ceiling or a wall. ( Pages 16 and 17)IMPORTANT: • Procure 3 screws (M4) to secure the camera to a cei

17Method of camera installationInstalling the camera directly on the ceiling or wallNote: • Use the installation template label (accessory) with the s

18IMPORTANT: • When inserting an SD memory card, make sure the direction. • Before removing the SD memory card, select "Not use" for &quo

19ConnectionCaution: • FOR UL LISTED MODEL(S), ONLY CONNECT POE 48 V CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60

2The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this

20Connection examplePoE device (hub)PCLAN cable(category 5 or better, straight)LAN cable(category 5 or better, straight)LAN cable(category 5 or better

21InstallationCamera mountingInstallation shall be conducted after turning off each device.  Remove the enclosure. ( Page 15) Connect the cables

22Adjustment Adjust the camera angle. When determining the camera angle, repeat fine adjustments by gradually moving the panning table and tilting

23Note: • Depending on the vertical/horizontal angle used, the edges of the camera may be projected. • Use Extra Zoom when you want to adjust the

24 Attach the enclosure to the camera with 2 enclosure fixing screws (M3) and the hook. (Recommended tightening torque: 0.4 N·m {0.3 lbf·ft})Enclosur

25Configuring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with default settings is configured. I

26 If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow the instructions of the wizard to start the instal

27TroubleshootingBefore asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after

28• BasicPower source: PoE (IEEE802.3af compliant)Power consumption: PoE 48 V: 110 mA/5.3 W(Class 2 device)Ambient operating temperature: 0 °C to +

29Focal length: 1.95 mm {5/64 inches}Maximum aperture ratio: 1:2.2Angular field of view: Horizontal: 100°, Vertical: 81° (3 megapixels [4:3] mode)

3ContentsImportant safety instructions ... 4Limi

30Cropping function: 2 megapixel [16:9] H.264 640×360/ 320×180 max. 30 fps MJPEG 640×360/ 320×180 max. 30 fps 1.3 megapixel [16:9] H.26

31Standard accessoriesOptional accessoriesInstallation Guide (this document) ... 2 pcs.Important Safety In

Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying docu

4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

5Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMI

6The network camera WV-SF138 is designed to operate using a PC on a network (10BASE-T/100BASE-TX). By connecting to a network (LAN) or the Internet, i

7System requirements for a PCCPU: Intel® CoreTM2 Duo 2.4 GHz or faster recommendedMemory: 512 MB or more (A minimum of 1 GB memory is required when u

8Trademarks and registered trademarks • Microsoft, Windows, Windows Vista, Internet Explorer, and DirectX are either registered trade-marks or trade

9PrecautionsRefer installation work to the dealer.Installation work requires technique and experi-ences. Failure to observe this may cause fire, elect