Panasonic SCHTB527 Provozní pokyny stáhnout pdf (Strana 11)

Getting started

Precautions

RQT9834

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

Supplied components

Commercially available components (not supplied)

≥Screws for wall mounting................................................................................................................... k 4

≥Fall prevention cord ........................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2



≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,

steel, concrete, etc.) and are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Locate the screwing positions on the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.

≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.

≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.

Screw eye

≥ Attach at a position capable of

supporting over 33 kg.

≥ Depending on the placement of

the main unit, the screwing

position of the screw eye may

differ.

When attaching the main unit to a wall

∏ 4 Safety holders ∏ 2 Wall mount brackets

∏ 2 Rear pads ∏ 2 Screws with

washer

∏ 2 Screws without

washer

A Wall mount bracket (supplied)



252 mm257 mm 233.5 mm 275.5 mm

1018 mm

75 mm

31.5 mm

43.5 mm

12.5 mm

A A

SC-HTB527EGEB_RQT9834-B.book 11 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Getting started

Precautions

RQT9834

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

Supplied components

Commercially available components (not supplied)

≥Screws for wall mounting................................................................................................................... k 4

≥Fall prevention cord ........................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2



≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,

steel, concrete, etc.) and are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Locate the screwing positions on the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.

≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.

≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.

G Screw eye

≥ Attach at a position capable of

supporting over 33 kg.

≥ Depending on the placement of

the main unit, the screwing

position of the screw eye may

differ.

When attaching the main unit to a wall

∏ 4 Safety holders ∏ 2 Wall mount brackets

∏ 2 Rear pads ∏ 2 Screws with

washer

∏ 2 Screws without

washer

A Wall mount bracket (supplied)



252 mm257 mm 233.5 mm 275.5 mm

1018 mm

75 mm

31.5 mm

43.5 mm

12.5 mm

A A

SC-HTB527EGEB_RQT9834-B.book 11 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Getting started

Precautions

RQT9834

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

Supplied components

Commercially available components (not supplied)

≥Screws for wall mounting................................................................................................................... k 4

≥Fall prevention cord ........................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2



≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,

steel, concrete, etc.) and are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Locate the screwing positions on the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.

≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.

≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.

G Screw eye

≥ Attach at a position capable of

supporting over 33 kg.

≥ Depending on the placement of

the main unit, the screwing

position of the screw eye may

differ.

When attaching the main unit to a wall

∏ 4 Safety holders ∏ 2 Wall mount brackets

∏ 2 Rear pads ∏ 2 Screws with

washer

∏ 2 Screws without

washer

A Wall mount bracket (supplied)



252 mm257 mm 233.5 mm 275.5 mm

1018 mm

75 mm

31.5 mm

43.5 mm

12.5 mm

A A

SC-HTB527EGEB_RQT9834-B.book 11 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Getting started

Precautions

RQT9834

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

Supplied components

Commercially available components (not supplied)

≥Screws for wall mounting................................................................................................................... k 4

≥Fall prevention cord ........................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2



≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,

steel, concrete, etc.) and are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Locate the screwing positions on the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.

≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.

≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.

G Screw eye

≥ Attach at a position capable of

supporting over 33 kg.

≥ Depending on the placement of

the main unit, the screwing

position of the screw eye may

differ.

When attaching the main unit to a wall

∏ 4 Safety holders ∏ 2 Wall mount brackets

∏ 2 Rear pads ∏ 2 Screws with

washer

∏ 2 Screws without

washer

A Wall mount bracket (supplied)



252 mm257 mm 233.5 mm 275.5 mm

1018 mm

75 mm

31.5 mm

43.5 mm

12.5 mm

A A

SC-HTB527EGEB_RQT9834-B.book 11 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Getting started

Precautions

RQT9834

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

Supplied components

Commercially available components (not supplied)

≥Screws for wall mounting................................................................................................................... k 4

≥Fall prevention cord ........................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ................................................................................. k 2



≥ Use commercially available screws with a nominal diameter of 4.0 mm, which are suitable to the material of the wall (e.g., wood,

steel, concrete, etc.) and are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Locate the screwing positions on the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Position the main unit with at least 50 mm of space above it. If not, it may not be possible to access the buttons.

≥ The position on the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg.

≥ Be sure to use a spirit level to ensure that both screwing positions are horizontal to each other.

G Screw eye

≥ Attach at a position capable of

supporting over 33 kg.

≥ Depending on the placement of

the main unit, the screwing

position of the screw eye may

differ.

When attaching the main unit to a wall

∏ 4 Safety holders ∏ 2 Wall mount brackets

∏ 2 Rear pads ∏ 2 Screws with

washer

∏ 2 Screws without

washer

A Wall mount bracket (supplied)



252 mm257 mm 233.5 mm 275.5 mm

1018 mm

75 mm

31.5 mm

43.5 mm

12.5 mm

A A

SC-HTB527EGEB_RQT9834-B.book 11 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

RQT9834

Komercijalno dostupne komponente (nisu isporučene)

• Vijci za postavljanje na zid ................................................................................................................. × 4

• Kabel za sprečavanje pada ............................................................................................................... × 2

• Vijak s ušicama (za pričvršćivanje kabela za sprečavanje pada) ...................................................... × 2

• Koristite komercijalno dostupne vijke s nominalnim promjerom od 4,0 mm koji odgovaraju materijalu zida (drvo, čelični

okvir, beton itd.) i imaju nosivost preko 33 kg.

• Koristite kabel koji ima nosivost preko 33 kg (promjera oko 1,5 mm).

Odredite mjesto za postavljanje vijaka na zid.

• Upotrijebite mjere navedene u nastavku da biste odredili mjesto za postavljanje vijaka na zid.

• Postavite glavnu jedinicu tako da je iznad nje barem 50 mm prostora. Inače neće biti moguće dosegnuti gumbe.

• Položaj na zidu gdje ćete postaviti vijke treba imati nosivost preko 33 kg, baš kao i sam vijak.

• Pomoću libele provjerite jesu li oba mjesta za postavljanje vijaka međusobno vodoravno položena.

Glavnu jedinicu postavite u željeni položaj i pričvrstite oba kabela na

policu ili stol.

• Napetost kabela mora biti minimalna.

Vijak s ušicom

• Pričvrstite na mjestu koje ima

nosivost preko 33 kg.

• Ovisno o tome kako ćete

postaviti glavnu jedinicu,

razlikovat će se položaj

postavljanja vijka s ušicom.

4 sigurnosna

držača

2 držača za

postavljanje na zid

2 stražnje

podloge

Držač za postavljanje na zid (isporučen)

2 vijka s

tiplama

2 vijka bez tipli

Pričvršćivanje glavne jedinice na zid

Isporučene komponente

Mjere oprezaPriprema

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 27 28

Komentáře k této Příručce

Žádné komentáře

Panasonic SCHTB527 Provozní pokyny Strana 11

Komentáře k této Příručce

Související produkty a manuály pro Reproduktorové sady Panasonic SCHTB527