Panasonic WJ-ND400 Průvodce nastavením Strana 27
- Strana / 110
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
27
1 Click the [Quick] button.
The "Quick" page will be displayed.
2 Configure each setting item.
Refer to "Setup items" mentioned below.
3 Click the [Set] button in the "Network setup"
section.
When the IP address of the client PC port is
changed, the following window will be displayed.
Click the [OK] button to apply the setting.
Note:
• WhentheIPaddressoftheclientPCportis
changed, all login users will forcibly be logged out.
It is necessary for users to access the changed IP
address to reconnect to the recorder.
• Whenthe"Linespeed"settingischangedandthe
[Set] button is clicked, the recorder will reboot.
Network settings
Configure the network settings of the recorder.
■ Network setup - Camera port/Client PC port
Configure the following setting items for each port.
[DHCP]
Select "On" or "Off" to determine whether or not to use
the DHCP server.
Select "On" to obtain an IP address, a subnet mask
and a gateway address from the DHCP server. Select
"Off" when entering values manually.
On: Uses the DHCP server.
Off (default): Does not use the DHCP server.
[IP address] *
1
When "Off" is selected for "DHCP", enter an IP
address.
[Subnet mask] *
1
Enter a subnet mask according to the network configu-
ration when "Off" is selected for "DHCP".
[Default gateway] *
1
Enter the address of the default gateway according to
the network configuration when "Off" is selected for
"DHCP".
[Line speed]
The following are available for "Line speed".
Auto (default)/1000M-Full/100M-Full/100M-Half/
10M-Full/10M-Half
■ Network setup - Maintenance port
[IP address] *
1
Enter an IP address.
[Subnet mask] *
1
Enter a subnet mask.
*1 Refer to page 11 about the default setting.
Important:
• Thenetworksettingsforeachport(IPaddress,etc.)
should be configured with a different subnet.
• When"On"isselectedfor"DHCP"andanyframe
rate other than "Off" is select for "SD memory rec.",
a request for writing data onto the SD memory card
demanded at the startup of the recorder may fail.
This error may occur when the response from the
DHCP server is slow.
However, a request for writing data onto the SD
memory card will be accepted once the addresses
have been obtained from the DHCP server.
Setup items
- WJ-ND400K 1
- WJ-ND400K/G 1
- Contents 2
- About the user manuals 3
- System requirements for a PC 3
- Abbreviations 4
- 4. When recording images 5
- 5. When copying images 6
- 8. Other 6
- Operation flow 7
- Setup menu and its items 8
- Network settings 11
- Network settings of a PC 13
- About the operation window 15
- Top page 17
- [Control] button 18
- [Cam. select] button 19
- [Setup] button 20
- Status display area 21
- Playback point operation area 22
- [HDD] tab 22
- [CAM] tab 24
- Quick settings 26
- 1 Click the [Quick] button 27
- Camera registration 28
- 7 Click the [OK] button 29
- 3 Click the [Set] button 30
- Basic settings 31
- 1 Click the [Basic] button 32
- 4 Click the [Set] button 32
- Emergency recording 34
- [Measurement] button 35
- SD memory rec 36
- How the event action is taken 38
- 1 Click the [Event] button 39
- 2 Click the [Basic] tab 39
- Schedule recording 43
- Setup items 44
- Time table 47
- NW camera 49
- 8 Click the [Set] button 50
- 5 Click the [Set] button 52
- 1 Click the [Camera] button 54
- 2 Click the [Group] tab 54
- 3 Enter the group titles 54
- 2 Click the [Sequence] tab 55
- 1 Click the [Server] button 57
- 2 Click the [NTP] tab 57
- 2 Click the [FTP] tab 58
- 2 Click the [Mail] tab 60
- 2 Click the [Proxy] tab 62
- 9 Click the [Set] button 64
- DNS setup 65
- Port forwarding 65
- Static route 66
- 2 Click the [DDNS] tab 67
- 2 Click the [SNMP] tab 68
- User management 70
- Edit the user settings 73
- Delete the user settings 73
- 2 Click the [Host] tab 74
- Edit the host settings 75
- Delete the host settings 75
- Maintenance 78
- Disk information 79
- 3 Check each item 82
- 2 Click the [Disk] tab 83
- Settings management 85
- Disk config 86
- Disk format 89
- Notification by e-mail 93
- Troubleshooting 96
- Glossary 103
- Panasonic Canada Inc 110
Související produkty a manuály pro Bezpečnostní kamery Panasonic WJ-ND400
Bezpečnostní kamery Panasonic WZ-CW380 Provozní pokyny
(218 stránky)
(218 stránky)
Bezpečnostní kamery Panasonic WJ-NV200 Provozní pokyny
(103 stránky)
(103 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce