Panasonic WJ-ND400 Průvodce nastavením stáhnout pdf (Strana 65)

Network setup - Camera port/Client PC port

■ DHCP

Select "On" or "Off" (default) to determine whether or

not to use the DHCP server.

Select "On" to obtain an IP address, a subnet mask

and a gateway address from the DHCP server. Set to

"Off" when entering the addresses above manually.

■ IP address *

When "Off" is selected for "DHCP", enter an IP

address.

■ Subnet mask *

Enter a subnet mask according to the network configu-

ration when "Off" is selected for "DHCP".

■ Default gateway *

Enter the gateway address according to the network

environment when "Off" is selected for "DHCP".

■ Line speed

The following are available for the line speed.

Auto (default)/1000M-Full/100M-Full/100M-Half/

10M-Full/10M-Half

Network setup - Maintenance port

■ IP address *

Enter an IP address.

■ Subnet mask *

Enter a subnet mask.

■ Static route

Determine whether or not to validate the static route

setting. To configure this setting, click the [Setup >>]

button.

DNS setup

■ DNS

Select "Manual" or "Auto" to enable to search the IP

address from the host name using the DNS. Select

"Off" when not using the DNS.

"Auto" is available only when "On" is selected for

"DHCP" (using the DHCP server). (Page 63)

"Manual" is available regardless of the "DHCP" setting

(using the DHCP server or not).

When "Manual" is selected for "DNS", enter the DNS

server addresses to "Primary server address" and

"Secondary server address".

Default: Off

■ Primary server address

Enter the IP address of the primary DNS server.

■ Secondary server address

Enter the IP address of the secondary DNS server.

■ Domain name

Enter the domain name of the recorder. (Default: local-

domain)

Enter up to 255 alphanumeric characters including

hyphens (-) and periods (.).

The first character of the domain name should be an

alphabetical character.

*1 Refer to page 11 about the default setting.

Important:

 • Thenetworksettingsforeachport(IPaddress,etc.)

should be configured with a different subnet.

 • When"On"isselectedfor"DHCP"andanyframe

rate other than "Off" is select for "SD memory rec.",

a request for writing data onto the SD memory card

demanded at the startup of the recorder may fail.

This error may occur when the response from the

DHCP server is slow.

However, a request for writing data onto the SD

memory card will be accepted once the addresses

have been obtained from the DHCP server.

Port forwarding

■ Port forwarding

Select "On" (default) or "Off" to determine whether or

not to set the port forwarding.

■ Port number

When selecting "On" for "Port forwarding", set numbers

from 1 - 65525 to the port numbers of each camera.

(Camera1: 60001 (default) - Camera64: 60064)

The following port numbers and the port numbers used

for the HTTP port, for the FTP port, for the site alarm

setting, and for the port forwarding are unavailable.

20, 21, 23, 25, 42, 53, 67, 68, 69, 79, 80, 105, 110, 123,

161, 162, 546, 547, 995, 10001, 10002, 10003, 10004,

10005, 10006, 10007

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 109 110

Komentáře k této Příručce

Žádné komentáře

Panasonic WJ-ND400 Průvodce nastavením Strana 65

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní kamery Panasonic WJ-ND400